Jeep Patriot Oil Capacity And Oil Type

If you have a Jeep Patriot, then you need to know the Jeep Patriot oil capacity. This is because it is important to keep your engine well-lubricated, and the only way to do that is by using the correct amount of oil. If you use too much or too little, it can damage your engine. In this article, we will show the Jeep Patriot oil capacity in detail so that you can be sure to use the right amount of oil for your vehicle.

2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 Jeep Patriot Oil Capacity And Oil Type

Engine 2.4L 4-cyl ED3 Engine 2.0L 4-cyl ECN Engine
Oil capacity with filter 4.5 quarts (4.3 liters) 4.5 quarts (4.3 liters)
Oil type 5W-20 5W-20
Oil pan drain plug tightening torque 30 ft/lbs 30 ft/lbs

Recommended Engine Oil For Jeep Patriot

API Certified SAE 5W-20 Engine Oil meets the requirements of FCA US Material Standard MS-6395, such as MOPAR, Pennzoil, and Shell Helix. The appropriate SAE grade is indicated on your engine oil filler cap.

If the vehicle is driven in a dusty and off-road environment or operated mostly at idle or only very low engine RPMs, change the oil every 4,000 miles (6,500 kilometers). This sort of operation is referred to as Severe Duty.

At Every Oil Change Interval As Indicated By Oil Change Indicator System:

  • Change oil and filter.
  • Rotate the tires. Rotate at the first sign of irregular wear, even if it occurs before the oil indicator system turns on.
  • Inspect battery and clean and tighten terminals as required.
  • Inspect brake pads, shoes, rotors, drums, hoses, and park brake.
  • Inspect engine cooling system protection and hoses.
  • Inspect exhaust system.
  • Inspect engine air cleaner if used in dusty or off-road conditions.

Benefits Of Using Synthetic Motor Oils

Conventional mineral engine oils are made from a mineral base oil that is (Group-I or Group-II) and usually has more contaminants as the main component.

Engine oils that are synthesized have several advantages for automobiles. – Lower viscosity, which translates to better cold-temperature performance (cold-start).

In general, synthetic engine oils outperform traditional mineral engine oils in a variety of ways. Synthetic oils are made with higher-quality base stocks (such as Group-III or PAO) that improve the overall performance package of engine oil.

Engine Oil Change Indicator System

Oil Change Required:

The engine oil change indicator system in your car tells you when it’s time to change the oil. After a single chime, the “Oil Change Required” notice will flash on the EVIC display for approximately 10 seconds to indicate that your next scheduled oil change is approaching. The engine oil change indication system is duty cycle-dependent, which means your driving habits may affect how often you have to change the engine oil.

This message will continue to show up every time you turn the ignition switch to the ON/RUN position, even if it has not been reset. To temporarily turn off the alert, press and release the Trip Odometer button on the instrument cluster. The oil change indicator system may be reset (after doing the required maintenance) by following these steps:

  • Turn the ignition switch to the ON position. Do not start the engine.
  • Fully depress the accelerator pedal, slowly, three times within 10 seconds.
  • Turn the ignition switch to the OFF/LOCK position

Jeep Patriot Oil Reset

An engine oil change indicator system is built into your car. After a single chime, the “Change Oil” warning will flash in the instrument cluster odometer for approximately 12 seconds to indicate when the next scheduled oil change interval begins.

The engine oil change warning system is duty cycle based, which implies the timing of your next oil change may vary depending on your driving habits. This message will reappear each time you switch the ignition key to the ON/RUN position unless it is reset.

To turn off the alert for a period of time, press and release the Trip Odometer button on the instrument cluster. To reset the oil change indicator system (after doing the scheduled maintenance), follow these steps.

  1. Turn the ignition switch to the ON position. Do not start the engine.
  2. Fully depress the accelerator pedal slowly three times within 10 seconds.
  3. Turn the ignition switch to the OFF/LOCK position.

NOTE: If the oil change indicator system does not reset, the indication light on your dashboard will illuminate when you start your car. If required, repeat this process.

Dan Hoffman

Dan is a co-founder of Engineswork. He knows everything about internal combustion engines. Ask your questions in comments down below this article - he will be glad to help you anytime.

Leave a Reply

Your email address will not be published.

Recent Posts